Automatic double end tenoner Celaschi TSA 280/DS - second hand

Make: 
Celaschi
Model: 
Tsa 280/ds
Description: 

AUTOMATIC DOUBLE END TENONER CELASCHI TSA 280

- MACHINE 1ST OR 2ND IN LINE
High performance machine.
Heavy-duty structure in welded and stress-released steel, dimensioned according to machineconfiguration
and length.
Fixed left Hand side – Right hand side movable along double
ground steel guides, with automatic lubrication.
Positioning control also possible with remote control board.
Safety relay to prevent start of the movable side while
chain-track is running and to prevent the track from running
while the movable side is being positioned.
The joining pins, in hardened-steel,16-mm diameter, run on
dust sealed- and life lubricated bearings .
Pop up dogs at every 400 mm distance
Chain-track covering pads are made in high resistance vulcanized rubber on steel plates.
The steel support plate is 2mm thick and is attached to the top of the chain-link by 4 screws.
The balanced transmission shaft (diameter 80-mm) has a large-size positive keyway and driving
sprocket
The sprockets are hardened in the contact points.
Top pressure beams have a single powered V-belt with clutch.
Infeeding and outfeed steel covers for chain protection.
The columns which hold the working units and saddle/slide supports
are made in solid cast-iron with precision ground dovetail guides.
Centralized lubrication system for all sliding surfaces of the
saddle-slide.
All operating units are tiltable 0-90 degrees.
All motors vertical/horizontal adjustment with Siko readouts
Electrical cabinet supplied with standard 3 m connecting cables.
Emergency stop cable at back, thickness safety on top
Pressure beams and stop press button on control cabinet.
Safety Photocells at front
CELASCHI TSA 280- 380V/3PH/50 hz- front chain extension mm 1100
- WORKING WIDTH MM 220 – 3,000
- WORKPIECE THICKNESS MM 8-80
- TOP PRESSURE BEAMS WITH DRIVE BELTS AND CLUTCH
- BOTTOM FEED CHAINS MM 80 WDTH WITH BEARINGS
- AUTOMATIC LUBRICATION OF BEDPLATES
- AUTOMATIC LUBRICATION OF FEED CHAINS
- POP UP DOGS DISTANCE 400 MM
- VARIABLE FEED SPEED 4-24 MT/MIN
- ELECTRONIC OPENING OF MOVABLE SIDE BY 2-SPEED MOTOR
(FAST/SLOW)
- ELECTRONIC LIFTING OF TOP PRESSURE BEAMS
- MANUALS AND ELECTRIC DIAGRAMS
- SEPARATE CONTROL CABINET
- VOLTS 380V/3ph/50 hertz
MACHINE EQUIPPED WITH :
- LH ADJUSTABLE INFEED SIDE FENCE- MANUAL HORIZONTAL ADJUSTMENT
1-2 JUMP CUTTING/SCORING UNITattached to hoggers
- MOTORS 1,6 KW (2.2HP) – 6000 RPM BY INVERTER
- TILTABLE 0-90 DEGREES
- shafts diam 25 X 28 L - max tool diam 150- DUST OUTLET DIA 80mm
3-4 HOGGING - 5.5/8 HP - 6000 RPM
- SHAFTS DIA 35x63 - Max tool diam 250mm
- DUST OUTLET DIAM 120mm
- TILTABLE 0-90 DEGREES
5-6 JUMP MILLING UNIT
- WITH PNEUMATIC JUMP IN/OUT
- HEAVY DUTY MOTORS 10 HP - 6000 RPM
- MOTORS IN VERTICAL POSITION
- SHAFTS DIA 40 x 240 - Max tool dia 250mm
-DUST OUTLET DIA 140mm
7-8 MILLING UNIT
- HEAVY DUTY MOTORS 10 HP - 6000 RPM
- MOTORS IN VERTICAL POSITION
- SHAFTS DIA 40 x 240 - Max tool dia 250mm - DUST OUTLET DIA 140mm
- DUST& SOUNDPROOF CABINETS
- MOTORS DRIVEN BY STATIC INVERTER
- MAIN DRIVE MOTOR - SPEED ADJUSTABLE BY INVERTER
- PLC CONTROL FOR SELECTION OF WORKING UNITS
- ELECTRONIC HEIGHT ADJUSTMENT (THICKNESS)
- ELECTRONIC WIDTH ADJUSTMENT, PROGRAMMABLE
- DUST AND SOUNDPROOF CABINETS

Contact

WM ENGINEERING SRL's picture
WM ENGINEERING SRL
ITALY
Thiene

+39 0445 382443

Contact seller

CAPTCHA
Please confirm that you are not a Robot. To prevent automated spam submissions.

Vertical Tabs