ROLL MATERIAL FOR STRAIGHT EDGES MM 0.4-3
EDGEMATERIALS THICKNESS MM 0.4-0.5 FOR SOFT
EDGEMATERAILS THICK MM 0.6-10 FOR STRAIGHT
PANEL THICKNESS MM 10-60
K87 VOLTAGE: 400V/50HZ with Neutral EU
Description:
- The machine rests on thick steel bases which
rest on the floor.
- The generously dimensioned modular steel beams
guarantee rectilinear feeding of panel.
- The bottom track is 70 mm wide with self lubricated
Pads riding on round/flat ground steel guides.
- Standard feed speed is from 10 to 26 M/1'.
- Transmission by means of a generously dimensio-
ned shaft.
- Top pressure beam with single drive belt and clutch
guided by spring loaded rods to guarantee perfect
feed of panel throught the working units
- Electric (automatic) lifting of top beams.
- Line control for pneumatic ON/OFF (no limit
Switches)
- The working units are connected to the upper
pressure beams for simultaneous height adjustm.
- Gearboxes for the transmission of the various
movements.
- The electric cabinet position at infeed of machine
and swivelling at various angles
- Panel thickness: from 10 to 50 mm
- Working height: from 965 to 970 mm
- Power supply 400 V 50 Hz (+N)
- Standard paint finish: graey RAL 9002
EXECUTION ACCORDING TO CE RULES
In accordance with Ce rules, 89/392 machines directive.
TRACK SPEED CONTROL
For speed adjustment of track feed from the numeric control.
ELECTRONIC POSITIONING OF TOP PRESSURE BEAM
For the adjustment of the top pressure beams from numeric control (comprising encoder and safety device).
DOUBLE MILLING/PROFILING UNIT UNIT RT-E KW 4
For profling the panel be edged prior to glueing
and assure an excellent surface for gluing:
- 2 high frequency motors with automatic time intervention to
avoid chipping on the panel;
- Motors tiltable 0-90 degrees;
- lateral slide feelers with digital numerical indicators for the shifting;
- exhaust hood with optimized chip suction flux;
- inverter.
Technical data:
Speed rpm 9000
Motor power kW 4+4
Max. section removal according
to the track speed mm² 90
Panel thickness mm 10-45
Tools installed 2 TCT cutters
D=100 H=49 Z=3+3
GLUING UNIT FOR SOFTFORMING VC34-34 FOR STRAIGHT OR SOFT
For the glueing of straight or shaped edges in coils and in strips
with hot melted glue:
- Double glue roller for glue applicatgion topane or edgematerials
- quick melt system
- Trace device of the glue pot on linear ball bearing guides
- Quick interchangeable glue pot
- control of the glue temperature on glue pot and on premelt system
- Edge presence control
- Guillotine shears for tape cut (max 3mm thick X 45)
- Automatic Edgestrips and coil feeding magazine (diam 800mm)
- pressure zone with pneumatic independent adjustment of the
pressure with Siko mechanical readout.
Teflon coated pressure rolls
- automatic ON/OFFf of the glue pot
Technical data:
Edge thickness mm 0,4-10
Edge height mm 12-63
Min. coil length mm 280
Min. strips length mm 260
Min. length of solid wood mm 360
Strip storage capacity mm 220
Glue pot capacity kg 1,6
Glue melting capacity kg/h 8
REVOLVER PRESSURE ZONE FOR STRAIGHT OR SOFTFORMED EDGES
- 1 POSITION FOR STRAIGHT EDGES
- 2 POSITIONS FOR PROFILED (SOFT)
COIL MAGAZINE (MAX. H=65)
Technical data:
Maximum roll Ø mm 800
Max. edge thickness mm 3
Max. edge height:
For thin edges up to 1 mm mm 65
For edges up to 3 mm mm 45
END TRIMMING UNIT KW 0,35
For the removal of the exceeding edge from the top and bottom of
the panel:
- two motors with pneumatic stroke
- front, back feeler with automatic intervention
- lateral feelers on linear ball recirculating guides with pneumatic
intervention
- motors with manual inclination up to 15°
- automatic cut-off.
Technical data:
Speed rpm 12000
Max. track speed (depending
on edge thickness) m/min 20
Motors power kW 0,35+0,35
Edge thickness mm 0,4-25
Max. edge section mm² 1100
Min. panel length mm 145
Distance between panels mm 600
Blade stroke mm 40
Tools installed nr.2 blades Ø 150 mm
FINE TRIMMING UNIT RSU KW 0,5
For the finishing of thin edges or wood or for the rough trimming
of the radius on PVC/ABS edges:
- two motors inclinable up to 30° with quick-release system
- top motor connected to the pressure beam for the automatic
adjustment according to the edge thickness
- disk-shaped vertical feelers of big diameter
- lateral disk feelers with independent horizontal adjustment
- numerical decimal indicators for the horizontal shifting of motors
and feelers
- horizontal and vertical automatic cut-off of 10 mm.
Technical data:
Speed rpm 12000
Motors power kw 0,5+0,5
Edge thickness mm 0,3-5
Min. Panel thickness
with cutters R=3 mm 13
Tools not installed
CORNER ROUNDING UNIT C1+C2
To carry out the front and back rounding on the transversal side
of shaped panels or on PVC/ABS edges and thin solid wood with
a very high degree of finishing:
- four motors provided with quick-release system with motor
block+tool supported by a parallelogram kinematic motion which allows the unit to follow the head (end) of the panel in sequence, independently from the geometry of the profile;
- separate processing sequences to avoid the simultaneity of working which could cause vibrations of the panel, provided with oscillating motion to follow the panel;
- copying system made with bearing feelers and lateral feeler;
- automatic cut-off.
Technical data:
Speed rpm 12000
Max. speed track feed m/min 22
Motors Power kW 0,35x4
Edge thickness mm 0,3-5
Min. concave profile radius mm 35
Minimum distance of panel:
18 m/min mm 460
22 m/min mm 470
Min. panel length:
18 m/min mm 170
22 m/min mm 220
Tools not installed
GLUE SCRAPER UNIT RCA/2C
It eliminates possible excess of glue on the top and bottom side of
the panel:
- completed with two cutter-tools of Widia;
- vertical feelers;
- two blowers which allows the cutters to be always clean;
- pneumatic intervention to assure the best processing of the starting and the ending side of the panel;
- automatic cut-off.
OSCILLATING BRUSHING UNIT SP/F
For the cleaning and finishing (shining) of plastic edges:
- two overlapped motors manually inclinable completed with two
cloth brushes;
- top motor connected to the pressure beam for the automatic
adjustment according to the thickness panel;
- manual cut-off.
Technical data:
Speed rpm 1500
Max. horizontal inclination 5°
Max. vertical inclination:
- with 8 mm panel 4°
- with 60 mm panel 8°
Motors power kW 0,29+0,29
Brushes dimension mm 150x50x33
PNEUMATIC ON/-OFF AND OSCILLATION
DOUBLE EDGE BRIGHTENING UNIT PH/1600
For brightening up the colours on ABS edges.
The unit receives air from the compressed air distribution system
and gives out hot air through two independent nozzles.
Technical data:
Power W 1400+1400
Tension V 220
INVERTER FOR MOTORS
- PLC CONTROL FOR SELECTION OF UNITS – UP TO99 PROGRAMMES – TRACK SPEED CONTROL – ON/OFF
(NO MICROSWITCHES) – THICKNESS ADJUSTMENT
- Italy
- Second hand
